800-435-4482
16-2448 Seymour Black Wrinkle Texture Spray Paint (12 oz)
Product Line: Automotive Specialty SKU: 16-2448DISCLAIMER: The color swatches provided are intended to closely represent the actual colors; however, please note that there may be variations from what is displayed on your screen.
$13.50
This is a durable black wrinkle paint that is gasoline and heat resistant. It has excellent hiding qualities and can be used where conventional coatings break down. Two coats are needed to achieve the wrinkled texture, with the second coat applied approximately three minutes after the first. The wrinkling effect does not appear immediately after spraying. Allow eight hours to cure.
- Paint can reproduce the original finish on a variey of car and truck parts
- Resists gasolinem automotive fluids, fading, rust, corrosion and chipping
- Excellent hiding qualities and can be used where conventional coating break down
- Up to 7 sq. ft. coverage per can
- Dry to touch 30 minutes; 8 hours is required to complete wrinkling process
| UPC: | 043281001281 |
| Part #: | 0000162448 |
| Container Size: | 16 OZ |
| Net Fill Wt. OZ: | 12 |
| Net Fill Wt. G: | 340 |
| Prop 65 (cancer): | yes |
| Prop 65 (repro): | yes |
| Safety Data Sheet: | View Safety Data Sheet  |
| Product Information Sheet: | View Product Information Sheet |
Question
Tony –
Would this work on a harley engine
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
Probably not, black wrinkle goes to 250F continuously. I would think the engine might get hotter than that. Please contact our technical support for more information. 815-895-9101
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Lee –
Do you need a primer?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
If the surface is clean and free of rust or contaminants, then you do not need a primer. That said, it’s a good idea, especially on wood or hard plastics.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
lee Pair –
is this a fine or course wrinkle. Using for 1966-69 chev corvair gauge cluster and glovebox panel and door!
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
Seymour’s wrinkle is more of a medium wrinkle.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Brett Fox –
How about Somebody just go get Joe from the back have him spray a few lines so we can see. Are the wrinkles big, small, in the middle how do we know let us see easy.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Michael Igel –
Is this a flat or gloss finish? 16-2448 Seymour Black Wrinkle Texture Spray Paint (12 oz)
Thank you
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
16-2448 is a non-flat coating, with a gloss finish.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Eric –
Can the paint be reapplied if the first attempt didn’t wrinkle throughout? I applied 16-2448 Black Wrinkle to freshly glass bead blasted aluminum valve cover. I sprayed the first coat on the heavy side, then waited 3 minutes for the second coat. I may have not applied as much as needed since I was worries about runs, the finish didn’t wrinkle at all in some spots. Question, can I simply respray the two coats on top of the existing wrinkle, or do I need to strip it back to bare metal and try again? Thanks
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
If the first attempt didn’t work, it’s best to strip the paint and start from scratch. Two medium coats 3 minutes apart at 70 degrees is recommended.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Joe Alexander –
Looking to coat my hot rod chassis with this, how’s the durability? And does anyone have a good picture of the finish?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
The coating is heat resistant to 250F continuous and offers good resistance to fuel and oil. Unfortunately, we do not have a photo of the finish.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
VÃctor verdugo –
Is this product will work on calipers?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
While it meets the heat requirements, however, would think the texture will allow brake dust/mud/etc. to collect.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Cary Newman –
Would this work to hide cracks and splits on a 1966 Ford pickup padded dash?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
Hairline cracks, yes. Anything larger would require a filler first.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Cary Newman –
Does the wrinkle paint require a primer before being applied on vinyl or bondo?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
No primer for vinyl (but you would want to scuff that surface to improve adhesion). For Bondo, I’d recommend our PBE sandable primers.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Lee –
And just be painted over, say with spray paint?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
No, this cannot be top coated.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Jake –
How would this hold up as a base coat on a set of valve covers to give the wrinkle texture then applying your higher heat engine enamel over top for correct color?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
It has a 250F heat resistance so it would hold up well by itself. It shouldn’t be top coated by anything.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Jonathan –
Do you need to apply heat/bake in an oven to achieve the wrinkle finish?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
No
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Edward Wuster –
What type of primer is recommended with hard plastic before applying 16-2448 Seymour Wrinkle paint?
Thank you
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
20-1672 PBE sandable black primer.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Zach –
What should I do and how do I proceed. I prepared my parts surface cleaned and degrease as I’ve done with a lot of parts. I shook the can plenty applied the first coat. Waited the appropriate time and applied the second coat. I let the product sit indoors where it didn’t get below 70 ish degrees. And only some spots wrinkled. The rest is a semi gloss smooth finish.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Answer
Seymour Paint –
On clean bare metal, no. Anything else it would be a good idea.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal